hallo,
habe soeben einen ibm netvista 6568 - arvdr aufgesetzt.
habe alles hinbekommen ausser lirc !!!
uart none eintraege in der autoserial.conf sind gemacht -
wie gehe ich nun vor??
wie bekomme ich lirc zum laufen??
gruss
hallo,
habe soeben einen ibm netvista 6568 - arvdr aufgesetzt.
habe alles hinbekommen ausser lirc !!!
uart none eintraege in der autoserial.conf sind gemacht -
wie gehe ich nun vor??
wie bekomme ich lirc zum laufen??
gruss
was sagt denn LIRC dazu?
Was fuer ArVDR version? 0.1RC2 oder 0.5? Kernel version?
hallo,
arvdr 05
soeben aufgesetzt und
apt-get update
apt-get upgrade
apt-get dist-upgrade
gemacht
kernel
2.6.15.7
ein dpkg reconfigure lirc hat mich auch nicht veitergebracht
ein
killall lircd
irrecord lalala.txt funktioniert nicht da nix ankommt
gruss
modprobe lirc-serial geht ohne meldung durch
bitte ausgabe von "dmesg" ins Studio
arvdr:~# dmesg
Linux version 2.6.15.7 (root@compaq) (gcc version 3.3.5 (Debian 1:3.3.5-13)) #3 PREEMPT Thu Jun 1 13:12:29 UTC 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000007ee06c0 (usable)
BIOS-e820: 0000000007ee06c0 - 0000000007ee66c0 (ACPI data)
BIOS-e820: 0000000007ee66c0 - 0000000007eee700 (ACPI NVS)
BIOS-e820: 0000000007eee700 - 0000000008000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
126MB LOWMEM available.
found SMP MP-table at 0009fe00
On node 0 totalpages: 32480
DMA zone: 4096 pages, LIFO batch:0
DMA32 zone: 0 pages, LIFO batch:0
Normal zone: 28384 pages, LIFO batch:7
HighMem zone: 0 pages, LIFO batch:0
DMI 2.3 present.
ACPI: RSDP (v000 IBM ) @ 0x000fdfe0
ACPI: RSDT (v001 IBM CDTPWSPI 0x00001010 IBM 0x00000000) @ 0x07ee6640
ACPI: FADT (v001 IBM CDTPWSPI 0x00001010 IBM 0x00000000) @ 0x07ee65c0
ACPI: MADT (v001 IBM CDTPWSPI 0x00001010 IBM 0x00000000) @ 0x07ee6540
ACPI: DSDT (v001 IBM CDTPWSPI 0x00001000 MSFT 0x01000007) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:8 APIC version 17
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
Using ACPI for processor (LAPIC) configuration information
Intel MultiProcessor Specification v1.1
Virtual Wire compatibility mode.
OEM ID: IBM-PCCO Product ID: CDT-BIOS MP APIC at: 0xFEE00000
I/O APIC #2 Version 32 at 0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
Processors: 1
Allocating PCI resources starting at 10000000 (gap: 08000000:f6c00000)
Built 1 zonelists
Kernel command line: vga=0F07 root=/dev/hda1 acpi=force quiet
mapped APIC to ffffd000 (fee00000)
Initializing CPU#0
PID hash table entries: 512 (order: 9, 8192 bytes)
Detected 631.327 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 123856k/129920k available (2854k kernel code, 5656k reserved, 1182k data, 172k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 1264.53 BogoMIPS (lpj=2529066)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
mtrr: v2.0 (20020519)
CPU: Intel Celeron (Coppermine) stepping 03
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 8e20)
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd55c, last bus=1
PCI: Using configuration type 1
ACPI: Subsystem revision 20050902
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
Boot video device is 0000:00:02.0
PCI quirk: region f800-f87f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region fc00-fc3f claimed by ICH4 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [PIN1] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [PIN2] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [PIN3] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [PIN4] (IRQs 3 4 5 6 7 9 10 11 12 14 *15)
ACPI: PCI Interrupt Link [PIN5] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [PIN6] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [PIN7] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [PIN8] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI2._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
PCI: Bridge: 0000:00:1e.0
IO window: 7000-7fff
MEM window: feb00000-febfffff
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:1e.0 to 64
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.25 [Flags: R/W].
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Processor [CPU0] (supports 8 throttling states)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel i815 Chipset.
agpgart: AGP aperture is 64M @ 0xf8000000
ACPI: PCI Interrupt Link [PIN1] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [PIN1] -> GSI 11 (level, low) -> IRQ 11
Console: switching to colour frame buffer device 80x30
I810FB: fb0 : Intel(R) 815 (Internal Graphics with AGP) Framebuffer Device v0.9.0
I810FB: Video RAM : 4096K
I810FB: Monitor : H: 29-30 KHz V: 60-60 Hz
I810FB: Mode : 640x480-8bpp@60Hz
intelfb: Framebuffer driver for Intel(R) 830M/845G/852GM/855GM/865G/915G/915GM chipsets
intelfb: Version 0.9.2
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
pktcdvd: v0.2.0a 2004-07-14 Jens Axboe (axboe@suse.de) and petero2@telia.com
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH2: IDE controller at PCI slot 0000:00:1f.1
ICH2: chipset revision 5
ICH2: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfff0-0xfff7, BIOS settings: hda:DMA, hdb:pio
Probing IDE interface ide0...
hda: Maxtor 6Y080P0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hda: max request size: 128KiB
hda: 160086528 sectors (81964 MB) w/7936KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
hda: hda1
libata version 1.20 loaded.
116x: driver isp116x-hcd, 05 Aug 2005
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt Link [PIN4] enabled at IRQ 15
PCI: setting IRQ 15 as level-triggered
ACPI: PCI Interrupt 0000:00:1f.2[D] -> Link [PIN4] -> GSI 15 (level, low) -> IRQ 15
PCI: Setting latency timer of device 0000:00:1f.2 to 64
uhci_hcd 0000:00:1f.2: UHCI Host Controller
uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1f.2: irq 15, io base 0x0000fb00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
sl811: driver sl811-hcd, 19 May 2005
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
ACPI wakeup devices:
PS2K UAR1 UAR2 USB0 PCI2
ACPI: (supports S0 S1 S3 S4 S5)
input: AT Translated Set 2 keyboard as /class/input/input0
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 172k freed
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda1, internal journal
Adding 131064k swap on /var/swapfile. Priority:-1 extents:35 across:148828k
ACPI: PCI Interrupt Link [PIN2] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [PIN2] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 55752 usecs
intel8x0: clocking to 41145
e100: Intel(R) PRO/100 Network Driver, 3.4.14-k4-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
ACPI: PCI Interrupt Link [PIN5] enabled at IRQ 9
PCI: setting IRQ 9 as level-triggered
ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [PIN5] -> GSI 9 (level, low) -> IRQ 9
e100: eth0: e100_probe: addr 0xfebff000, irq 9, MAC addr 00:02:55:0C:6F:05
Linux video capture interface: v1.00
saa7146: register extension 'dvb'.
ACPI: PCI Interrupt Link [PIN3] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:01:0a.0[A] -> Link [PIN3] -> GSI 5 (level, low) -> IRQ 5
saa7146: found saa7146 @ mem c896ee00 (revision 1, irq 5) (0x13c2,0x0000).
DVB: registering new adapter (Technotrend/Hauppauge WinTV DVB-S rev1.X or Fujitsu Siemens DVB-C).
adapter has MAC addr = 00:d0:5c:5b:a7:cd
dvb-ttpci: info @ card 0: firm f0240009, rtsl b0250018, vid 71010068, app 80f22623
dvb-ttpci: firmware @ card 0 supports CI link layer interface
dvb-ttpci: adac type set to 0 @ card 0
saa7146_vv: saa7146 (0): registered device video0 [v4l2]
ves1x93: Detected ves1893a rev2
DVB: registering frontend 0 (VLSI VES1x93 DVB-S)...
input: DVB on-card IR receiver as /class/input/input1
dvb-ttpci: found av7110-0.
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
saa7146: unregister extension 'dvb'.
ACPI: PCI interrupt for device 0000:01:0a.0 disabled
Linux video capture interface: v1.00
saa7146: register extension 'dvb'.
ACPI: PCI Interrupt 0000:01:0a.0[A] -> Link [PIN3] -> GSI 5 (level, low) -> IRQ 5
saa7146: found saa7146 @ mem cc9bee00 (revision 1, irq 5) (0x13c2,0x0000).
DVB: registering new adapter (Technotrend/Hauppauge WinTV DVB-S rev1.X or Fujitsu Siemens DVB-C).
adapter has MAC addr = 00:d0:5c:5b:a7:cd
dvb-ttpci: info @ card 0: firm f0240009, rtsl b0250018, vid 71010068, app 80f22623
dvb-ttpci: firmware @ card 0 supports CI link layer interface
dvb-ttpci: adac type set to 0 @ card 0
saa7146_vv: saa7146 (0): registered device video0 [v4l2]
ves1x93: Detected ves1893a rev2
DVB: registering frontend 0 (VLSI VES1x93 DVB-S)...
input: DVB on-card IR receiver as /class/input/input2
dvb-ttpci: found av7110-0.
saa7146: register extension 'budget dvb'.
saa7146: register extension 'budget_ci dvb'.
saa7146: register extension 'budget_av'.
usbcore: registered new driver ttusb
usbcore: registered new driver ttusb-dec
b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully
usbcore: registered new driver b2c2_flexcop_usb
usbcore: registered new driver cinergyT2
lirc_dev: IR Remote Control driver registered, at major 61
lirc_serial: no version for "lirc_unregister_plugin" found: kernel tainted.
lirc_serial: auto-detected active high receiver
lirc_dev: lirc_register_plugin: sample_rate: 0
arvdr:~#
habe eine dvb-s 1.3 im system
also keinen onboard ir reciever....
hab ich da im setup was verbockt??
nute einen selbstgelцteten ir reciever am comport.
jetzt Inhalt von /var/lib/setserial/autoserial.conf und ausgabe
setserial /dev/ttyS0
setserial /dev/ttyS1
und an welchem port ist LIRC angeschlossen?
autoserial.conf :
#
###PORT STATE GENERATED USING AUTOSAVE-ONCE###
###AUTOSAVE-ONCE###
###AUTOSAVE-ONCE###
###AUTOSAVE###
#
# If you want to configure this file by hand, use
# dpkg --configure setserial
# and change the configuration mode of the file to MANUAL. If you do not do this# this file may be overwritten automatically the next time you upgrade the
# package.
#
/dev/ttyS0 uart none
/dev/ttyS1 uart none
#/dev/ttyS1 uart 16550A port 0x02f8 irq 3 baud_base 115200 spd_normal skip_test
ausgabe setserial /dev/ttyS0
/dev/ttyS0, UART: unknown, Port: 0x03f8, IRQ: 4
ausgabe setserial /dev/ttyS1
/dev/ttyS1, UART: unknown, Port: 0x02f8, IRQ: 3
wo er angeschlossen ist weiss ich nicht - hab aus verzweiflung im moment 2 reciever dran
hm....nichts Verdaechtiges .... sind da vielleicht mehr als 2 comports (setserial /dev/ttyS[23] ? sind die LIRC's funktionsfaehig?
die lircs sind klasse - von den 2 anderen vdrs
ja es scheint 4 zu geben da ich auch ausgaben bei ttys2 und ttyS3 bekomme
erst bei ttyS4 sagt er no such device
/dev/ttyS0 uart none
/dev/ttyS1 uart none
/dev/ttyS2 uart none
/dev/ttyS3 uart none
in autoserial.conf brachte nix...
tja...jetzt weiss du was zu tun ist? die 2 aufsuchen ...oder probier mal ьber BIOS zu regeln ...viel spass
im bios sehe ich nur 2
kann dort adreesen und irq ґs aendern -
soll ich das machen??
hm
damit kannst du die 2 nur swap'en .... sonst gibt's nichts? jetzt bin ich ratlos
hm bringt nix
wo kann ich testen oder vergeben das lirc die anderen ports nutzt?
wo traegt man das ein zb ttyS2 oder ttyS3???
bin ratlos
lirc_dev: IR Remote Control driver registered, at major 61
lirc_serial: no version for "lirc_unregister_plugin" found: kernel tainted.
lirc_serial: auto-detected active high receiver
lirc_dev: lirc_register_plugin: sample_rate: 0
Sollte es nicht active low receiver heiЯen ,wenn der Empfдnger sauber erkannt ist?
jep
und das bedeutet???
bitte was muss ich tun?
habs nun raus !!!
hab das bios geupdated -
Пожалуйста зарегистрируйся для просмотра данной ссылки на страницу.
und anschliessend die adresse und irq von com 2 auf irq4 und 0x3f8 umgestellt - standardmaessig waren dort andere werte...
nach reboot sagt er nun active low receiver
und es funzt
danke fuer die hilfe
best wishes